Your Position: Home > News

Grouting Plant
Grout Mixer and Agitator
Grout Pump
Refractory Gunite/Mixer
Shotcrete Machine
Industrial Peristaltic Pump
Foam Concrete Machine
Soil Spraying Machine
Concrete Pump
Plaster Machine
hydraulic pump station
Customized Service

TEL

86-371-63902781

skype:

machine.machine6

Email

sales@leadcrete.com

FAX

86-371-63526676

ADDRESS

Xisihuan Ring-Road East, Tielu, Xiliu Lake sub-district, Zhongyuan District, Zhengzhou, Henan China

China supplier of piston mortar pump

2019-11-11 19:13:33

China supplier of piston mortar pump 

Leadcrete is an experienced supplier of piston mortar pump. Piston mortar pump is a single-acting piston pump. The piston mortar pump uses the motor as the power to drive the crankshaft to rotate through the transmission and deceleration. Thereby driving the crank to reciprocate, so that the piston reciprocates in the piston cylinder, thereby causing vacuum in the suction chamber of the slurry pump slurry (the outlet valve is closed at this time), sucking the slurry into the pump cylinder and then discharging the one-way The valve delivers the slurry to the high pressure storage chamber (when the suction port check valve is closed), and finally the slurry for construction is output from the slurry pipe of the piston mortar pump.

Supplier of piston mortar pump


Piston mortar pump sold by the Leadcrete supplier uses a cam-type transmission, the piston structure is automatically controlled and set, the flow rate is large, and the service life is long. This machine is mainly used for pressure conveying, plastering various dry premixed mortar, plastering mortar, lime mortar, insulating fireproof mortar, ground mortar, adhesive mortar, masonry mortar, reinforced mortar, filling mortar, pouring mortar, insulation Mortar, fiber mortar, self-leveling mortar, repair and reinforcement mortar. The piston mortar pump has the advantages of compact structure, reliable operation, low failure rate, convenient cleaning, easy maintenance and high pumping pressure.

piston mortar pump supplier


Piston mortar pump by Leadcrete suppliers are widely used in urban construction, tunnels, bridges, road traffic projects, water conservancy projects and wall plastering throughout crack grouting. China supplier of piston mortar pump can also be used to produce a variety of insulation, waterproof, soundproof new boards. It can also be used in construction machinery, interior and exterior wall plastering and spray mortar, exterior wall insulation mortar spraying, material mortar blank, fire resistant coating, large building fireproofing material, waterproof coating, etc.

China supplier of piston mortar pump


As an experienced piston mortar pump supplier, Leadcrete will briefly share the operation and precautions of the mortar pump:
1. Do not allow water or mortar to flow into the motor or electrical control components, otherwise it will cause a short circuit.
2. The piston mortar pump should not be repaired, adjusted and refueled while it is working.
3. Pay attention to whether the pump, motor, etc. are running normally. If there is abnormal situation, stop immediately. Open the discharge valve first and then eliminate the fault.
4. The piston mortar pump pressure gauge reading should be observed frequently. If the set pressure is exceeded and the power is not automatically shut down, stop immediately and restart after troubleshooting.
5. If the pump slurry is blocked, the discharge valve should be opened immediately to relieve pressure. When removing the pump head, pay attention to safety.
6, the slurry transport mortar is best to run continuously, try to avoid stopping. If you need to stop in the middle, the interval should be as follows: for lime mortar, should not exceed 30 minutes; for mixed mortar or ready-mix mortar, should not exceed 20 minutes; for on-site mixing of cement mortar, should not exceed 10 minutes. If the above time is exceeded, the pump should be started every 4~5 minutes to slow down the mortar and avoid clogging. If you need to stop for a long time, you should open the discharge valve to relieve pressure and clean.
7. It is important to note that in the event of blockage or pressure, the pipe joint cannot be loosened directly and must be relieved before being released.
8. The operator cannot let the connector face him-self and others while releasing the connector.
If you would like to know more about the supplier of China piston mortar pump and Leadcrete piston mortar pump, please feel free to contact us, we will be the first time to help you, our email:sales@leadcrete.com 

China of piston mortar pump